Device Integrations

What garage door opener works with Home Assistant?

Which garage door openers work with Home Assistant: local controllers like ratgdo and Konnected blaQ, Tailwind, Meross, DIY relays, plus safety tips.

On this page
  1. Check your opener’s protocol first
  2. Local controllers
  3. DIY relays with a door sensor
  4. Cloud options
  5. How Home Assistant shows the door
  6. Safety

Most garage door openers can work with Home Assistant, but the right approach depends on the opener’s wall-control protocol. Add a local controller that speaks your opener’s protocol, such as ratgdo or Konnected GDO blaQ, and you get local control and a real open or closed state. The myQ app has no official Home Assistant integration.

Check your opener’s protocol first

The learn button on the back of the motor unit tells you what you’re dealing with. Check your manual to confirm, because colors are typical rather than guaranteed.

  • Yellow, red, orange, purple or brown learn button: Security+ or Security+ 2.0. ratgdo and the Konnected blaQ both support these.
  • White learn button: Security+ 3.0, found on newer openers. As of this writing, ratgdo and blaQ don’t support it.
  • No learn button, just a plain push button on two terminals: a dry-contact opener. A relay wired across the wall-button terminals can trigger it.

A common mistake is wiring a relay across the terminals of a Security+ 2.0 opener. Those openers use an encrypted, rolling-code conversation, so a simple contact closure doesn’t make the door move. A protocol-aware controller is the fix.

Local controllers

ratgdo is an ESP-based board that wires to the wall-control terminals. It runs locally, using ESPHome or MQTT. It supports Security+ 1.0, Security+ 2.0 and dry-contact openers, and it reports door, light, lock and obstruction states. Prices change, so check the current price before you buy.

Konnected GDO blaQ is a pre-built ESPHome device for Security+ openers. It works locally and doesn’t need a build. It doesn’t support Security+ 3.0.

Tailwind iQ3 has a core Tailwind integration. It’s local, and it supports up to three doors.

Meross garage controllers (MSG100 and MSG200) pair locally through the HomeKit Device integration. A HACS project, meross_lan, is another option. Some Security+ 2.0 setups need extra steps from the vendor, so check compatibility before you buy.

DIY relays with a door sensor

A dry-contact relay can press the wall button for you. A Shelly 1 or a Zigbee dry-contact relay can pulse the wall-button terminals for about half a second to one second. Not every Shelly is dry contact. The Shelly 1 and 1 Plus relays are, but the 1PM is not, so check the model. See Shelly devices in Home Assistant for setup details.

A relay on its own can’t tell you whether the door is open or closed. Add a reed switch or tilt sensor on the door, and use that for the state.

Cloud options

Genie uses the core Aladdin Connect integration, which is cloud-based. Reliability has varied, so test it before you depend on it.

myQ has no official Home Assistant integration. Home Assistant removed its myQ integration in 2023. Community HACS projects connect through the myQ cloud, but they can break when the vendor changes its service. For the wider appliance picture, see connecting appliances to Home Assistant.

How Home Assistant shows the door

A garage door appears as a cover entity with the garage device class. Its states are open, closed, opening and closing. You can control it with cover.open_cover, cover.close_cover and cover.toggle.

Matter garage door support is limited, and it depends on the product. Check the product’s documentation before you choose a Matter route.

Safety

  • Never bypass the photo-eye safety sensors, and don’t build anything that forces the door past a blocked beam.
  • Automated closing should warn before the door moves, using a sound or a flashing light, and give someone time to cancel it.
  • Unplug the opener, or switch off its breaker, before you wire anything.

The complete guide to device integrations

Adding and Managing Devices in Home Assistant: Integrations and Device Classes
Read the guide

Keep exploring

Guides from other topics

All topics →